# EPRLocksmith

> Mobile locksmith from Ashford for lock repairs, replacements and emergency call-outs


## Posts

- [Locksmith Farnham 088](https://eprlocksmith.co.uk/locksmith-farnham-088/): A Farnham customer had been told a cat flap could not be fitted without replacing the door, but I installed it neatly through the existing moulded panel.
- [Locksmith Chesham 087](https://eprlocksmith.co.uk/locksmith-chesham-087/): A Chesham window had worn hinges, draughts and closing problems, so I fitted new hinges from stock and lubricated the mechanism.
- [Locksmith Aldershot 086](https://eprlocksmith.co.uk/locksmith-aldershot-086/): An Aldershot customer wanted a Yale keyless-entry system in place of the existing nightlatch, so I corrected the old installation and fitted the new system.
- [Locksmith Hook 085](https://eprlocksmith.co.uk/locksmith-hook-085/): A Hook customer wanted a cat flap fitted into a reinforced flat side-door panel, so I cut the opening, installed the unit and sealed it against water ingress.
- [Locksmith Ashford 084](https://eprlocksmith.co.uk/locksmith-ashford-084/): Every sealed glazing unit in an Ashford ground-floor flat had misted, so I measured and replaced them, including toughened glass for the kitchen-door sidelight.
- [Locksmith Walton-on-Thames 083](https://eprlocksmith.co.uk/locksmith-walton-on-thames-083/): A Walton-on-Thames customer had lost the keys to a barn door, so I fitted a British Standard deadlock and a standard nightlatch from stock.
- [Locksmith Staines 082](https://eprlocksmith.co.uk/locksmith-staines-082/): A Staines multipoint lock failed again after an earlier cam-swap repair lasted nearly two years, so I fitted a full replacement system.
- [Locksmith Ashford 081](https://eprlocksmith.co.uk/locksmith-ashford-081/): An Ashford front door had a neglected mechanism, loose fixings and rusty standard-security locks, so I serviced it and fitted higher-security cylinders.
- [Locksmith Chesham 080](https://eprlocksmith.co.uk/locksmith-chesham-080/): A Chesham customer wanted locks fitted to two internal doors, so I installed matching hardware to suit the existing lever-on-rose handles.
- [Locksmith High Wycombe 079](https://eprlocksmith.co.uk/locksmith-high-wycombe-079/): A High Wycombe door would not open because the latch was not retracting fully, so I opened it and fitted a genuine replacement gearbox from stock.
- [Locksmith Feltham 078](https://eprlocksmith.co.uk/locksmith-feltham-078/): A Feltham front door was jammed shut with a spinning handle and failed multipoint mechanism, so I opened it and fitted the replacement next day.
- [Locksmith Sunbury 077](https://eprlocksmith.co.uk/locksmith-sunbury-077/): A Sunbury customer wanted a cat flap in a toughened double-glazed patio door, so I fitted a new sealed unit manufactured with the opening precut.
- [Locksmith Sunbury 076](https://eprlocksmith.co.uk/locksmith-sunbury-076/): A Sunbury front-door multipoint gearbox had failed, so I fitted a genuine replacement from stock and adjusted the door.
- [Locksmith Staines 075](https://eprlocksmith.co.uk/locksmith-staines-075/): A Staines patio door was jammed shut even with the key, so I accessed the failed gearbox, opened the door and fitted a replacement from stock.
- [Locksmith Feltham 074](https://eprlocksmith.co.uk/locksmith-feltham-074/): A Feltham front-door multipoint system failed after an internal component bent and broke, so I fitted a replacement and adjusted the hinges.
- [Locksmith Staines 073](https://eprlocksmith.co.uk/locksmith-staines-073/): A Staines customer needed a recently fitted lock replaced after malicious damage, so I fitted the same replacement and checked the rest of the locking system.
- [Locksmith Staines 072](https://eprlocksmith.co.uk/locksmith-staines-072/): A Staines front door was blocked shut by a failed multipoint gearbox, so I released the mechanism and replaced the gearbox, handles and cylinder.
- [Locksmith Shepperton 071](https://eprlocksmith.co.uk/locksmith-shepperton-071/): A Shepperton garden door needed a cat flap and replacement misted glazing, so I fitted a reinforced lower panel, new glass and the cat flap.
- [Locksmith Shepperton 070](https://eprlocksmith.co.uk/locksmith-shepperton-070/): A Shepperton customer had failing multipoint locks on both front and garden doors, so I replaced the mechanisms and checked the doors for excess resistance.
- [Locksmith Staines 069](https://eprlocksmith.co.uk/locksmith-staines-069/): A Staines door would not lock because the multipoint system could not fully engage, so I confirmed the diagnosis and realigned the door.
- [Locksmith Ashford 068](https://eprlocksmith.co.uk/locksmith-ashford-068/): An Ashford Yale nightlatch would open from outside but not inside because the internal lever pin had sheared, so I replaced the complete system.
- [Locksmith Farnborough 067](https://eprlocksmith.co.uk/locksmith-farnborough-067/): A Farnborough tenant could not operate a locked window handle and had no key, so I released it, fitted a replacement and checked the mechanism.
- [Locksmith Ashford 066](https://eprlocksmith.co.uk/locksmith-ashford-066/): An Ashford nightlatch key became increasingly difficult to turn. Cleaning only helped temporarily, so I replaced the unreliable rim cylinder.
- [Locksmith Feltham 065](https://eprlocksmith.co.uk/locksmith-feltham-065/): A Feltham uPVC door was locked shut after most of the gearbox spindle broke away, so I secured it overnight and fitted a replacement mechanism next day.
- [Locksmith Twickenham 064](https://eprlocksmith.co.uk/locksmith-twickenham-064/): A Twickenham aluminium window mechanism failed completely and the original part was obsolete, so I adapted a stock replacement and adjusted the keeps.
- [Locksmith Ashford 063](https://eprlocksmith.co.uk/locksmith-ashford-063/): An Ashford multipoint lock had intermittent faults, so I fitted a genuine replacement and then replaced that unit at no extra cost when its latch proved faulty.
- [Locksmith Walton-on-Thames 062](https://eprlocksmith.co.uk/locksmith-walton-on-thames-062/): A Walton sliding door had a shattered spindle inside a factory-sealed multipoint mechanism, so I created controlled access, repaired it and adjusted the rollers.
- [Locksmith Surbiton 061](https://eprlocksmith.co.uk/locksmith-surbiton-061/): A Surbiton customer wanted his nightlatch converted to a Yale battery-powered keyless system, so I fitted the customer-supplied kit professionally.
- [Locksmith Iver 060](https://eprlocksmith.co.uk/locksmith-iver-060/): An Iver shed lock was damaged during an attempted break-in, so I replaced the light-duty unit with a more robust bar-style lock.
- [Locksmith Bagshot 059](https://eprlocksmith.co.uk/locksmith-bagshot-059/): A Bagshot bathroom window had deteriorated hinges and could no longer close, so I fitted a new hinge set from van stock.
- [Locksmith Isleworth 058](https://eprlocksmith.co.uk/locksmith-isleworth-058/): An Isleworth patio door would not latch and was badly draughty, so I realigned it and replaced the lock, handles and full multipoint mechanism.
- [Locksmith Walton-on-Thames 057](https://eprlocksmith.co.uk/locksmith-walton-on-thames-057/): A Walton bedroom window was draughty because the old hinge no longer sealed the sash properly, so I fitted heavy-duty hinges with an integrated restrictor.
- [Locksmith Hayes 056](https://eprlocksmith.co.uk/locksmith-hayes-056/): A Hayes internal sliding door developed repeat problems after an earlier repair lasted over a year, so I fitted a correctly measured replacement kit.
- [Locksmith Slough 055](https://eprlocksmith.co.uk/locksmith-slough-055/): A Slough tenant had an unreliable front-door nightlatch, so the landlord chose a British Standard replacement fitted from van stock.
- [Locksmith Richmond 054](https://eprlocksmith.co.uk/locksmith-richmond-054/): A Richmond bi-fold door had an intermittent locking fault caused by a sheared gearbox component, so I sourced and fitted the replacement next day.
- [Locksmith Isleworth 053](https://eprlocksmith.co.uk/locksmith-isleworth-053/): An Isleworth tenant needed a new aluminium-window handle, so I fitted the replacement and identified an unresolved alignment problem.
- [Locksmith Isleworth 052](https://eprlocksmith.co.uk/locksmith-isleworth-052/): An Isleworth uPVC window was difficult to close because the hinge was badly distorted, so I replaced it from stock and restored normal operation.
- [Locksmith Reading 051](https://eprlocksmith.co.uk/locksmith-reading-051/): A Reading front door had a failed multipoint gearbox and severe misalignment, so I replaced the gearbox and cylinder and spent around an hour realigning it.
- [Locksmith Staines 050](https://eprlocksmith.co.uk/locksmith-staines-050/): A Staines door had badly worn hinges, some held together with zip ties, so I replaced the hinge set and realigned the door.
- [Locksmith Hampton 049](https://eprlocksmith.co.uk/locksmith-hampton-049/): A Hampton door could no longer lock and its original multipoint mechanism was discontinued, so I secured it overnight and fitted a three-part replacement.
- [Locksmith Twickenham 048](https://eprlocksmith.co.uk/locksmith-twickenham-048/): A worn Twickenham nightlatch would no longer latch reliably, so I fitted a like-for-like replacement and adjusted the keep to stop the door rattling.
- [Locksmith Walton-on-Thames 047](https://eprlocksmith.co.uk/locksmith-walton-on-thames-047/): A Walton window would not open even though its locking mechanism worked, so I investigated from the adjacent window and found two screws holding the sash shut.
- [Locksmith Marlow 046](https://eprlocksmith.co.uk/locksmith-marlow-046/): A Marlow sliding door would not lock after the gearbox failed, so I secured it overnight and fitted the replacement multipoint mechanism next day.
- [Locksmith West Drayton 045](https://eprlocksmith.co.uk/locksmith-west-drayton-045/): A West Drayton bi-fold door became difficult to operate after a hinge failed, so I replaced the hinge and realigned the door leaves.
- [Locksmith Isleworth 044](https://eprlocksmith.co.uk/locksmith-isleworth-044/): A large Isleworth tilt-and-turn window would not close properly, so I fitted a replacement handle and adjusted the surrounding locking system.
- [Locksmith Ashford 043](https://eprlocksmith.co.uk/locksmith-ashford-043/): An Ashford patio door was locked shut by an obsolete multipoint system, so I preserved the high-security cylinder and fitted a three-part replacement next day.
- [Locksmith Ashford 042](https://eprlocksmith.co.uk/locksmith-ashford-042/): An Ashford customer wanted deadlocks fitted to three narrow internal doors while keeping the existing matching handles, so I installed separate locks below them.
- [Locksmith Staines 041](https://eprlocksmith.co.uk/locksmith-staines-041/): A Staines French patio door was difficult to close because the multipoint gearbox had worn out, so I fitted a replacement from stock.
- [Locksmith High Wycombe 040](https://eprlocksmith.co.uk/locksmith-high-wycombe-040/): A High Wycombe front door had an intermittently failing gearbox and tired handles, so I confirmed the fault and fitted both replacements next day.
- [Locksmith Weybridge 039](https://eprlocksmith.co.uk/locksmith-weybridge-039/): A Weybridge shutter-door lock trapped the key after the cylinder overturned, so I upgraded the cylinder and later replaced the ageing gearbox.
- [Locksmith Feltham 038](https://eprlocksmith.co.uk/locksmith-feltham-038/): A Feltham uPVC sliding door would not lock after previous work had damaged the gearbox casing, so I replaced it and adjusted the rollers and frame keep.
- [Locksmith Isleworth 037](https://eprlocksmith.co.uk/locksmith-isleworth-037/): An Isleworth garden door would not close because the frame had shifted and was missing fixing screws, so I secured and realigned it.
- [Locksmith Isleworth 036](https://eprlocksmith.co.uk/locksmith-isleworth-036/): An Isleworth aluminium bi-fold door was out of alignment and forcing the key, so I replaced the damaged gearbox and adjusted the frame keeps.
- [Locksmith Richmond 035](https://eprlocksmith.co.uk/locksmith-richmond-035/): A Richmond bedroom window was draughty and would not shut properly because the hinges were worn, so I fitted new hinges and a restrictor.
- [Locksmith Staines 034](https://eprlocksmith.co.uk/locksmith-staines-034/): A Staines front door was getting harder to open and close because the multipoint gearbox was no longer retracting fully, so I replaced it from stock.
- [Locksmith Eastfield 033](https://eprlocksmith.co.uk/locksmith-eastfield-033/): An Eastfield garden door had a damaged multipoint gearbox with missing gear teeth, so I replaced it from van stock during the first visit.
- [Locksmith Feltham 032](https://eprlocksmith.co.uk/locksmith-feltham-032/): A Feltham window had become increasingly difficult to close until the hinges failed, so I fitted a new pair and restored normal operation.
- [Locksmith Ashford 031](https://eprlocksmith.co.uk/locksmith-ashford-031/): An Ashford customer was left holding a broken door handle, so I ordered the unusual-size replacement pair and fitted them the following day.
- [Locksmith Ashford 030](https://eprlocksmith.co.uk/locksmith-ashford-030/): An Ashford premises had four specialist window-grille locks with no keys, so I ordered keyed-alike replacements and fitted all four.
- [Locksmith Ashford 029](https://eprlocksmith.co.uk/locksmith-ashford-029/): An Ashford garden-door gearbox failed after a spindle component sheared off, so I replaced the obsolete multipoint system the following day.
- [Locksmith Mayfair 028](https://eprlocksmith.co.uk/locksmith-mayfair-028/): A Mayfair customer wanted better premises security, so I fitted British Standard replacement locks without altering the door and retained its original escutcheons.
- [Locksmith Wembley 027](https://eprlocksmith.co.uk/locksmith-wembley-027/): A Wembley aluminium tilt-and-turn window was blocked shut with a spinning handle, so I opened it without damage and fitted the sourced replacement next day.
- [Locksmith Weybridge 026](https://eprlocksmith.co.uk/locksmith-weybridge-026/): Two uPVC windows in Weybridge needed failed gearboxes and hinges replacing after water ingress and broken locking components were found.
- [Locksmith Woking 025](https://eprlocksmith.co.uk/locksmith-woking-025/): A Woking front-door lock had an intermittent fault, so I opened the gearbox and removed a displaced spring and ball bearing as a temporary repair.
- [Locksmith Ashford 024](https://eprlocksmith.co.uk/locksmith-ashford-024/): A failed multipoint gearbox in Ashford was replaced from van stock, followed by a British Standard thumb-turn lock upgrade.
- [Locksmith Walton-on-Thames 023](https://eprlocksmith.co.uk/locksmith-walton-on-thames-023/): A Walton aluminium bi-fold door sometimes took ten minutes to open, so I diagnosed the failed component and later fitted the genuine replacement.
- [Locksmith Walton-on-Thames 022](https://eprlocksmith.co.uk/locksmith-walton-on-thames-022/): A Walton self-locking front door was hard to open because the bottom hook was badly out of alignment, so I moved the keep and improved the operation.
- [Locksmith Isleworth 021](https://eprlocksmith.co.uk/locksmith-isleworth-021/): An Isleworth aluminium window would not lock correctly after an upper mechanism plate broke away, so I adjusted the system and restored operation.
- [Locksmith Windsor 020](https://eprlocksmith.co.uk/locksmith-windsor-020/): A Windsor wooden front door would not open after its gearbox failed, so I preserved the cylinder and fitted a full-length replacement multipoint system.
- [Locksmith Ashford 019](https://eprlocksmith.co.uk/locksmith-ashford-019/): An Ashford door had intermittent double-locking problems, so I tested the fault and replaced the unreliable multipoint gearbox.
- [Locksmith Walton-on-Thames 018](https://eprlocksmith.co.uk/locksmith-walton-on-thames-018/): A Walton door would not lock because its key-operated multipoint gearbox had failed internally, so I sourced and fitted the replacement next day.
- [Locksmith Ashford 017](https://eprlocksmith.co.uk/locksmith-ashford-017/): An Ashford flat-door nightlatch had become so difficult to use that the customer resorted to pliers, so I fitted a British Standard replacement.
- [Locksmith Ashford 016](https://eprlocksmith.co.uk/locksmith-ashford-016/): An Ashford customer wanted the front-door lock changed, so I gained access without drilling and fitted a 3-star cylinder with an internal thumb-turn.
- [Locksmith Croydon 015](https://eprlocksmith.co.uk/locksmith-croydon-015/): A Croydon patio sliding door had a broken internal lock component, so I sourced an alternative replacement and adapted the existing keep.
- [Locksmith Staines 014](https://eprlocksmith.co.uk/locksmith-staines-014/): A Staines front door had become very difficult to lock, so I repaired the gearbox using a matching donor component from an identical mechanism.
- [Locksmith Walton-on-Thames 013](https://eprlocksmith.co.uk/locksmith-walton-on-thames-013/): A Walton bi-fold door had a hinge hanging on by about 1 mm of frame, so I stabilised it and later fitted the genuine upgraded replacement.
- [Locksmith Staines 012](https://eprlocksmith.co.uk/locksmith-staines-012/): A Staines fire-exit door lock had become difficult to turn, so I identified the existing lock and fitted a more practical thumb-turn replacement.
- [Locksmith Sunbury 011](https://eprlocksmith.co.uk/locksmith-sunbury-011/): A Sunbury back door that would not shut was repaired after broken gearbox parts were found and a genuine replacement part fitted.
- [Locksmith Borehamwood 010](https://eprlocksmith.co.uk/locksmith-borehamwood-010/): A Borehamwood customer wanted the front-door locks converted for a Yale Linus smart lock, so I fitted the sashlock, handles, smart lock and keypad.
- [Locksmith Bracknell 009](https://eprlocksmith.co.uk/locksmith-bracknell-009/): A Bracknell customer needed broken lead-pattern window glass replaced, so I measured the glazing and returned six working days later to install it.
- [Locksmith Kingston 008](https://eprlocksmith.co.uk/locksmith-kingston-008/): A Kingston upon Thames customer wanted the cat-flap glazing removed and the original stored unit refitted, so I changed the glazing and adjusted the door.
- [Locksmith High Wycombe 007](https://eprlocksmith.co.uk/locksmith-high-wycombe-007/): A High Wycombe uPVC window was stuck shut with part of its three-point locking system failing, so I opened it and replaced the faulty component.
- [Locksmith Thames Ditton 006](https://eprlocksmith.co.uk/locksmith-thames-ditton-006/): A Siegenia Aubi sliding patio door handle in Thames Ditton was repaired after the spindle shifted and corrosion seized the external mechanism.
- [Locksmith Thames Ditton 005](https://eprlocksmith.co.uk/locksmith-thames-ditton-005/): A deadlocking nightlatch was added to an outward-opening door in Thames Ditton while the existing sash lock body was retained.
- [Locksmith High Wycombe 004](https://eprlocksmith.co.uk/locksmith-high-wycombe-004/): A replacement timber front door in High Wycombe needed extensive planing and chiselling before being fitted with BS EN-compliant hinges.
- [Locksmith Hemel Hempstead 003](https://eprlocksmith.co.uk/locksmith-hemel-hempstead-003/): A Screen With Envy composite side gate with a key lock was assembled and installed in Hemel Hempstead.
- [Locksmith Walton-on-Thames 002](https://eprlocksmith.co.uk/locksmith-walton-on-thames-002/): A uPVC door in Walton-on-Thames had a freely spinning cylinder caused by a snapped gearbox pin; the gearbox was replaced from van stock.
- [Locksmith Camberley 001](https://eprlocksmith.co.uk/locksmith-camberley-001/): A discontinued aluminium sliding patio-door gearbox in Camberley was opened, repaired with a compatible component and refitted.
- [Locksmith Wrecclesham 188](https://eprlocksmith.co.uk/locksmith-wrecclesham-188/): A damaged leaded double-glazed unit in Wrecclesham was measured, ordered and replaced with the original lead pattern matched.
- [Locksmith Godalming 187](https://eprlocksmith.co.uk/locksmith-godalming-187/): A Godalming uPVC front door was badly misaligned and difficult to lock, so I used heel-and-toe adjustment to restore normal multipoint operation.
- [Locksmith Isleworth 186](https://eprlocksmith.co.uk/locksmith-isleworth-186/): An Isleworth shop entrance was rubbing hard against its glass frame, so I adjusted the frame spacing and restored proper clearance.
- [Locksmith Feltham 185](https://eprlocksmith.co.uk/locksmith-feltham-185/): A Feltham communal door had a badly installed keep cut back to the brick, so I rebuilt the fixing area and added an anti-thrust plate.
- [Locksmith Sunbury 184](https://eprlocksmith.co.uk/locksmith-sunbury-184/): A Sunbury French-door slave lock had a spinning handle and failed gearbox component, so I repaired the existing multipoint mechanism with the correct spare.
- [Locksmith Ashford 183](https://eprlocksmith.co.uk/locksmith-ashford-183/): An Ashford customer was locked out even with the key because the nightlatch snib had moved, so I manipulated it and reopened the door without replacement.
- [Locksmith Ashford 182](https://eprlocksmith.co.uk/locksmith-ashford-182/): An Ashford multipoint lock would not secure because a broken spring piece was blocking the gearbox bolt, so I repaired and retained the original mechanism.
- [Locksmith Ashford 181](https://eprlocksmith.co.uk/locksmith-ashford-181/): An obsolete Ashford multipoint lock stopped responding to the handles after a spindle push plate slipped out of position, so I repaired the original gearbox.
- [Locksmith Richmond 180](https://eprlocksmith.co.uk/locksmith-richmond-180/): A Richmond flat door had a failed multipoint lock that would not operate properly, so I replaced the failed component from van stock.
- [Locksmith Hersham 179](https://eprlocksmith.co.uk/locksmith-hersham-179/): A copied key snapped deep inside a Yale lock in Hersham. The difficult key profile made extraction unusually stubborn, but the existing lock was saved.
- [Locksmith Carshalton 178](https://eprlocksmith.co.uk/locksmith-carshalton-178/): A Carshalton uPVC garden-door lock lasted about another year after earlier lubrication before finally failing, so I fitted a genuine replacement and adjusted the door.
- [Locksmith Woking 177](https://eprlocksmith.co.uk/locksmith-woking-177/): A Woking uPVC door would not lock because the multipoint hooks only travelled halfway, so I replaced the failed gearbox after lubrication did not help.
- [Locksmith Staines 176](https://eprlocksmith.co.uk/locksmith-staines-176/): A high-security door lock in Staines failed and kept turning from the inside, so I replaced the faulty cylinder with another high-security option from stock.
- [Locksmith Ashford 175](https://eprlocksmith.co.uk/locksmith-ashford-175/): An Ashford front-door key became trapped after locking because the cylinder cam had shifted out of position, so I fitted a high-security replacement.
- [Locksmith Ashford 174](https://eprlocksmith.co.uk/locksmith-ashford-174/): An Ashford front-door multipoint lock failed when the gearbox spindle stopped engaging, so I repaired the obsolete system using a compatible donor component.
- [Locksmith Ashford 173](https://eprlocksmith.co.uk/locksmith-ashford-173/): An Ashford high-security front-door cylinder failed when its core partially pulled out, so I replaced the lock from stock and restored normal operation.
- [Locksmith Isleworth 172](https://eprlocksmith.co.uk/locksmith-isleworth-172/): An Isleworth uPVC door was badly misaligned and the key snapped under repeated force, so I replaced the cylinder and corrected the alignment.
- [Locksmith Sunbury 171](https://eprlocksmith.co.uk/locksmith-sunbury-171/): A Sunbury customer wanted privacy locks on two fire-rated bedroom doors, so I fitted 3-inch-backset locks while retaining matching long-plate handles.
- [Locksmith Ashford 170](https://eprlocksmith.co.uk/locksmith-ashford-170/): An Ashford exterior hardwood door received a new fire-rated sashlock, replacement handle and British Standard 3-star euro cylinder.
- [Locksmith Windsor 169](https://eprlocksmith.co.uk/locksmith-windsor-169/): A Windsor front-door latch stopped springing back because the gearbox spring had broken, so I repaired the existing multipoint mechanism.
- [Locksmith Sunbury 168](https://eprlocksmith.co.uk/locksmith-sunbury-168/): A Sunbury top-hung uPVC window dropped out of alignment and damaged its hinge, so I fitted a new pair of hinges and readjusted the sash.
- [Locksmith Bracknell 167](https://eprlocksmith.co.uk/locksmith-bracknell-167/): A Bracknell front-door multipoint lock only retracted about 80%, leaving the locking points projecting, so I sourced and fitted the correct replacement.
- [Locksmith Sunbury 166](https://eprlocksmith.co.uk/locksmith-sunbury-166/): A Sunbury French door was badly misaligned and chipping the opposite frame because the top hinge had broken, so I replaced the hinge and realigned the doors.
- [Locksmith Feltham 165](https://eprlocksmith.co.uk/locksmith-feltham-165/): A Feltham uPVC door was badly misaligned, warped and difficult to close, so I used heel-and-toe, hinge and lock adjustments to restore operation.
- [Locksmith Bracknell 164](https://eprlocksmith.co.uk/locksmith-bracknell-164/): A Bracknell window was unusable because the handle had stopped engaging the mechanism, so I confirmed the mechanism was sound and fitted a replacement handle.
- [Locksmith Ashford 163](https://eprlocksmith.co.uk/locksmith-ashford-163/): An Ashford front-door cylinder had become difficult to turn because of internal wear, so I fitted and adjusted a suitable replacement from van stock.
- [Locksmith Staines 162](https://eprlocksmith.co.uk/locksmith-staines-162/): A Staines tenant snapped the last key in a Yale nightlatch, so I replaced the barrel, cleaned the lock and corrected parts of the previous installation.
- [Locksmith Staines 161](https://eprlocksmith.co.uk/locksmith-staines-161/): A Staines side door was jammed shut after poor alignment broke the gearbox spindle, so I opened the door, replaced the gearbox and corrected the alignment.
- [Locksmith Ashford 160](https://eprlocksmith.co.uk/locksmith-ashford-160/): An Ashford front-door multipoint lock stopped working from outside, so I repaired the gearbox using a compatible spare component and restored normal operation.
- [Locksmith Gerrards Cross 159](https://eprlocksmith.co.uk/locksmith-gerrards-cross-159/): A Gerrards Cross window was blocked shut by a failed gearbox, so I opened it, dealt with incompatible rod connections and restored the mechanism.
- [Locksmith Ashford 158](https://eprlocksmith.co.uk/locksmith-ashford-158/): Friends in Ashford needed a new bathroom door and privacy lock in their first home, so I fitted the door and installed the new lock and furniture.
- [Locksmith Ashford 157](https://eprlocksmith.co.uk/locksmith-ashford-157/): An Ashford aluminium porch door had only part of its original lock remaining, so I fitted a new backbox and rim lock while keeping the antique front cover.
- [Locksmith Ashford 156](https://eprlocksmith.co.uk/locksmith-ashford-156/): An Ashford exterior door handle sheared off, so I replaced it and adjusted the hinges and multipoint lock to reduce the resistance on the new handle.
- [Locksmith Ashford 155](https://eprlocksmith.co.uk/locksmith-ashford-155/): An Ashford flat door would only open from inside with the key because the handle spindle had slipped out of engagement, so I repaired the spindle connection.
- [Locksmith Staines 154](https://eprlocksmith.co.uk/locksmith-staines-154/): A Staines high-security nightlatch jammed with the door shut. I managed to open it without destructive removal and identified the failed internal part.
- [Locksmith NW London 153](https://eprlocksmith.co.uk/locksmith-nw-london-153/): A rental-property front-door lock in NW London was rough to operate, so I stripped, cleaned, lubricated and realigned the existing mechanism.
- [Locksmith Ashford 152](https://eprlocksmith.co.uk/locksmith-ashford-152/): An Ashford patio-door multipoint gearbox had developed intermittent faults, so I removed the mechanism and fitted a replacement from van stock.
- [Locksmith Feltham 151](https://eprlocksmith.co.uk/locksmith-feltham-151/): A Feltham front-door cylinder projected too far beyond the handle plate, creating an avoidable security weakness and showing why correct sizing matters.
- [Locksmith Hemel Hempstead 150](https://eprlocksmith.co.uk/locksmith-hemel-hempstead-150/): A Hemel Hempstead flat entrance door and frame were badly out of alignment, so I adjusted the door and removed conflicting security pins as an interim repair.
- [Locksmith Ascot 149](https://eprlocksmith.co.uk/locksmith-ascot-149/): An Ascot electric garage door only opened halfway because a side spring had snapped, so I replaced the failed parts and readjusted the system.
- [Locksmith Hampton 148](https://eprlocksmith.co.uk/locksmith-hampton-148/): A Hampton up-and-over garage door had snapped cables and was sitting crooked, so I fitted new cones, cables and anti-drop rollers.
- [Locksmith Walton-on-Thames 147](https://eprlocksmith.co.uk/locksmith-walton-on-thames-147/): A Walton-on-Thames patio door had a grinding gearbox with broken parts rattling inside, so I replaced it from stock and adjusted the locking system.
- [Locksmith Walton-on-Thames 146](https://eprlocksmith.co.uk/locksmith-walton-on-thames-146/): A Walton-on-Thames flat-door cylinder had become difficult to use, so I replaced it with a British Standard thumb-turn option after discussing safer internal escape.
- [Locksmith Windsor 145](https://eprlocksmith.co.uk/locksmith-windsor-145/): A Windsor front-door multipoint lock had an intermittent internal fault caused by loose retaining parts, so I repaired and secured the existing gearbox.
- [Locksmith Twickenham 144](https://eprlocksmith.co.uk/locksmith-twickenham-144/): A Twickenham garden door was locked shut after the key snapped in an old sash lock, so I opened the failed lock and fitted a replacement from stock.
- [Locksmith Hounslow 143](https://eprlocksmith.co.uk/locksmith-hounslow-143/): A Hounslow front door was damaged during a break-in and would no longer lock, so I fitted an equivalent multipoint mechanism and new centre keep.
- [Locksmith Weybridge 142](https://eprlocksmith.co.uk/locksmith-weybridge-142/): A Weybridge garage-access door was locked shut after a deadlock screw shifted the internal gearing and blocked the mechanism completely.
- [Locksmith Farnham 141](https://eprlocksmith.co.uk/locksmith-farnham-141/): A Farnham conservatory-door glazing panel was smashed by a grass strimmer, so I measured, ordered and fitted a matching toughened double-glazed unit.
- [Locksmith Aldershot 140](https://eprlocksmith.co.uk/locksmith-aldershot-140/): An Aldershot customer wanted a cat flap fitted into an internal hollow-core door, so I marked, cut and installed the unit neatly in the agreed position.
- [Locksmith Teddington 139](https://eprlocksmith.co.uk/locksmith-teddington-139/): A Teddington customer wanted the front-door lock changed after moving in, so I replaced the obsolete setup with a British Standard nightlatch in a matching finish.
- [Locksmith Isleworth 138](https://eprlocksmith.co.uk/locksmith-isleworth-138/): Tenants in an Isleworth flat were trapped inside after the nightlatch failed, so I helped release the door and replaced the worn backbox and rim lock.
- [Locksmith Teddington 137](https://eprlocksmith.co.uk/locksmith-teddington-137/): A Teddington patio-door multipoint mechanism had become stiff after years without maintenance, so I removed, cleaned, lubricated and refitted the system.
- [Locksmith Hounslow 136](https://eprlocksmith.co.uk/locksmith-hounslow-136/): A failed bedroom-door latch in Hounslow was opened without damage and replaced with a fire-rated latch from van stock.
- [Locksmith Weybridge 135](https://eprlocksmith.co.uk/locksmith-weybridge-135/): A Weybridge multipoint lock had a broken gearbox spindle, but an unused spindle position allowed me to repair and retain the original mechanism.
- [Locksmith Loudwater 134](https://eprlocksmith.co.uk/locksmith-loudwater-134/): A Loudwater bi-fold door needed manufacturer-supplied warranty parts fitted after an emergency opening, so I installed and adjusted the new mechanism.
- [Locksmith Hatfield 133](https://eprlocksmith.co.uk/locksmith-hatfield-133/): A Hatfield patio door had a failed multipoint gearbox with a sheared internal component, so I replaced it from stock and checked the door alignment.
- [Locksmith Ashford 132](https://eprlocksmith.co.uk/locksmith-ashford-132/): An Ashford front-door multipoint lock was only retracting halfway, so I secured the door temporarily and sourced the correct replacement mechanism.
- [Locksmith Byfleet 131](https://eprlocksmith.co.uk/locksmith-byfleet-131/): Two Byfleet top-hung uPVC windows were catching the frame and one would not lock, so I replaced hinges and fitted the correct replacement mechanism.
- [Locksmith Feltham 130](https://eprlocksmith.co.uk/locksmith-feltham-130/): Non-destructive entry in Feltham after the customer lost her house keys while shopping, using a remote-controlled thumb-turn tool through the letterbox.
- [Locksmith Staines 129](https://eprlocksmith.co.uk/locksmith-staines-129/): A Staines front-door cylinder failed when its core pulled out and released the internal pins, so I fitted an updated like-for-like replacement from stock.
- [Locksmith Langley 128](https://eprlocksmith.co.uk/locksmith-langley-128/): A Langley uPVC window was stuck open with an obsolete low-handle mechanism, so I secured it temporarily and returned with the updated replacement.
- [Locksmith Windsor 127](https://eprlocksmith.co.uk/locksmith-windsor-127/): A Windsor customer wanted the rim lock and deadbolt upgraded and keyed alike, so I sourced matching higher-security locks operated by one key.
- [Locksmith Feltham 126](https://eprlocksmith.co.uk/locksmith-feltham-126/): A Feltham composite door was jammed after an attempted break-in, so I opened the failed multipoint system and fitted a genuine replacement mechanism.
- [Locksmith Chertsey 125](https://eprlocksmith.co.uk/locksmith-chertsey-125/): A Chertsey deadlock would only turn halfway because debris and previous forcing had damaged the levers, so I opened it and fitted a British Standard replacement.
- [Locksmith Molesey 124](https://eprlocksmith.co.uk/locksmith-molesey-124/): A Molesey tilt-and-turn door would not close after the bottom pivot pulled away from rotten timber, so I rebuilt and reinforced the hinge area.
- [Locksmith Ashford 123](https://eprlocksmith.co.uk/locksmith-ashford-123/): An Ashford multipoint lock was first repaired after a small internal part shifted, then failed months later and needed replacement after a lockout.
- [Locksmith Datchet 122](https://eprlocksmith.co.uk/locksmith-datchet-122/): A Datchet customer wanted extra front-door security, so I fitted a Yale nightlatch carefully within the limited space beside the glazing.
- [Locksmith Bracknell 121](https://eprlocksmith.co.uk/locksmith-bracknell-121/): Several Bracknell windows had draughts and closing problems, so I sourced compatible replacement hinges and adjusted a swollen timber frame.
- [Locksmith Ashford 120](https://eprlocksmith.co.uk/locksmith-ashford-120/): An Ashford front door had a grinding multipoint gearbox close to failure, so I replaced it, adjusted the hinges and fitted a British Standard cylinder.
- [Locksmith Staines 119](https://eprlocksmith.co.uk/locksmith-staines-119/): A Staines youth-club digital code lock failed after trapping a staff member in a supply room, so I replaced the faulty unit from van stock.
- [Locksmith Ashford 118](https://eprlocksmith.co.uk/locksmith-ashford-118/): An Ashford business door could lock from inside but not outside because the cylinder had shifted, so I repositioned and secured the existing lock.
- [Locksmith Purley 117](https://eprlocksmith.co.uk/locksmith-purley-117/): A Purley multipoint lock was unreliable because a screw had worked loose, so I secured it, serviced the mechanism and adjusted the door hinges.
- [Locksmith Ashford 116](https://eprlocksmith.co.uk/locksmith-ashford-116/): An Ashford garden-door multipoint lock had become unreliable and obsolete, so I secured it overnight and fitted a complete replacement system next day.
- [Locksmith Ashford 115](https://eprlocksmith.co.uk/locksmith-ashford-115/): An Ashford front door was jammed shut by a failed gearbox, so I opened it, replaced the gearbox and cylinder and repaired a sheared handle screw.
- [Locksmith Hounslow 114](https://eprlocksmith.co.uk/locksmith-hounslow-114/): A Hounslow B&B tilt-and-turn window had been badly damaged during an earlier repair attempt, so I converted it to usable side-hinged operation when parts could not be sourced.
- [Locksmith East Molesey 113](https://eprlocksmith.co.uk/locksmith-east-molesey-113/): An East Molesey front door was blocked shut by a failed multipoint lock, so I opened it and adapted a stock replacement when the original had a long lead time.
- [Locksmith Staines 112](https://eprlocksmith.co.uk/locksmith-staines-112/): A Staines customer wanted to improve front-door security, so I replaced the existing standard nightlatch with a higher-security option.
- [Locksmith Slough 111](https://eprlocksmith.co.uk/locksmith-slough-111/): A Slough garage door had lost keys, a missing handle and poor previous work, so I replaced the lock, handle and plate assembly.
- [Locksmith Surbiton 110](https://eprlocksmith.co.uk/locksmith-surbiton-110/): A Surbiton garden-door lock became increasingly difficult to use, so I replaced it with a British Standard sash lock and adjusted the keep.
- [Locksmith Camberley 109](https://eprlocksmith.co.uk/locksmith-camberley-109/): A Camberley sliding-door glazing unit was shattered by a stone while gardening, so I measured and fitted a toughened, UV-resistant replacement.
- [Locksmith SW London 108](https://eprlocksmith.co.uk/locksmith-sw-london-108/): A customer in SW London wanted the lock changed after misplacing a key, so I sourced the correct fire-rated cog euro cylinder for the multipoint system.
- [Locksmith Ashford 107](https://eprlocksmith.co.uk/locksmith-ashford-107/): An Ashford front door would not open because the latch was no longer retracting fully, so I replaced the failed part and corrected the door alignment.
- [Locksmith Sunbury 106](https://eprlocksmith.co.uk/locksmith-sunbury-106/): A Sunbury bi-fold door handle failed through wear rather than a jammed mechanism, so I sourced and fitted the genuine replacement.
- [Locksmith Richmond 105](https://eprlocksmith.co.uk/locksmith-richmond-105/): Richmond bi-fold doors had become badly misaligned and were digging into the bottom frame, so I spent around two hours realigning and improving them.
- [Locksmith Ashford 104](https://eprlocksmith.co.uk/locksmith-ashford-104/): An Ashford window was blocked shut because only one side of the locking mechanism released, so I opened it carefully and fitted a replacement part.
- [Locksmith South Croydon 103](https://eprlocksmith.co.uk/locksmith-south-croydon-103/): A South Croydon uPVC garden door was difficult to lock after years without servicing, so I cleaned and lubricated the mechanism and replaced the handle springs.
- [Locksmith Ashford 102](https://eprlocksmith.co.uk/locksmith-ashford-102/): An Ashford front-door multipoint gearbox became so unreliable that the family used the side door, so I replaced the intermittent gearbox from stock.
- [Locksmith Ashford 101](https://eprlocksmith.co.uk/locksmith-ashford-101/): An Ashford customer was locked out when the wind blew the front door shut, so I opened it non-destructively without damaging the lock or door.
- [Locksmith Stanwell 100](https://eprlocksmith.co.uk/locksmith-stanwell-100/): A Stanwell Moor garden-door multipoint lock had an intermittently jamming hook, so I secured it temporarily and fitted a genuine replacement.
- [Locksmith Twickenham 099](https://eprlocksmith.co.uk/locksmith-twickenham-099/): A Twickenham bi-fold door was rubbing because the bottom support hinge had worn, so I fitted a specialist replacement and realigned the full system.
- [Locksmith Twickenham 098](https://eprlocksmith.co.uk/locksmith-twickenham-098/): A stiff Twickenham front-door deadlock jammed during testing, so I removed the failing lock and fitted a British Standard replacement.
- [Locksmith Dorking 097](https://eprlocksmith.co.uk/locksmith-dorking-097/): A Dorking cloakroom door kept being left open, so I fitted fire-rated sprung hinges and adjusted the tension for safe self-closing operation.
- [Locksmith Walton-on-Thames 096](https://eprlocksmith.co.uk/locksmith-walton-on-thames-096/): A Walton-on-Thames window mechanism failed prematurely because the sash was out of alignment, so I replaced it and corrected the keep alignment.
- [Locksmith Ashford 095](https://eprlocksmith.co.uk/locksmith-ashford-095/): An Ashford front door would no longer lock because the multipoint gearbox had failed, so I replaced the riveted gearbox from van stock and adjusted the system.
- [Locksmith Watford 094](https://eprlocksmith.co.uk/locksmith-watford-094/): A Watford bathroom window would not lock because the mechanism had broken apart, so I removed the top-hung sash and fitted a replacement part from stock.
- [Locksmith Thames Ditton 093](https://eprlocksmith.co.uk/locksmith-thames-ditton-093/): A Thames Ditton customer needed glazing installed in a timber garden office, so I levelled the units, packed the door and checked the weatherproofing.
- [Locksmith Hounslow 092](https://eprlocksmith.co.uk/locksmith-hounslow-092/): A Hounslow shop glass door was rubbing at the bottom and needed a lock change after lost keys, so I adjusted the door and serviced the locking system.
- [Locksmith Kingston 091](https://eprlocksmith.co.uk/locksmith-kingston-091/): A Kingston customer wanted clear glazing above a wooden door replaced with a frosted double-glazed unit for better privacy and insulation.
- [Locksmith Ashford 090](https://eprlocksmith.co.uk/locksmith-ashford-090/): An Ashford uPVC French door had badly deteriorated hinges that were difficult to source, so I found the correct replacements and realigned the doors.
- [Locksmith Ashford 089](https://eprlocksmith.co.uk/locksmith-ashford-089/): An Ashford French door would not lock after its obsolete multipoint gearbox failed, so I realigned the doors and fitted a replacement mechanism.
- [Locksmith Stanwell 288](https://eprlocksmith.co.uk/locksmith-stanwell-288/): A failed multipoint gearbox left a Stanwell front door refusing to open, despite the mechanism sounding as though it was retracting.
- [Locksmith Sunbury 287](https://eprlocksmith.co.uk/locksmith-sunbury-287/): A stiff timber front door in Sunbury was planed to restore smooth operation, then fitted with a replacement nightlatch and deadbolt.
- [Locksmith Feltham 286](https://eprlocksmith.co.uk/locksmith-feltham-286/): Customer from Feltham called saying that several of the property's windows were having issues. Some would lock, some wouldn't, some were jammed shut, but most needed attention.
- [Locksmith Hounslow 285](https://eprlocksmith.co.uk/locksmith-hounslow-285/): Customer from Hounslow called saying he was having problems with the front door and it was becoming increasingly difficult for them to double-lock it. Double-locking, for those of you who haven't got this type of multipoint locking system, means lifting the handle and turning the key so the door isn't just held on the latch — the bolts or rollers are engaged too.
- [Locksmith Molesey 284](https://eprlocksmith.co.uk/locksmith-molesey-284/): Customer from Molesey got in touch regarding the front door, which was becoming more and more difficult to lock and unlock.
- [Locksmith Walton-on-Thames 283](https://eprlocksmith.co.uk/locksmith-walton-on-thames-283/): Former customer from Walton got in touch regarding an aluminium bi-fold door that wasn't locking properly anymore and was leaving gaps at the top when shut.
- [Locksmith Ruislip 282](https://eprlocksmith.co.uk/locksmith-ruislip-282/): Customer from Ruislip rang saying that he would like to change the lock on the garden gate. Easier said than done.
- [Locksmith Hampton 281](https://eprlocksmith.co.uk/locksmith-hampton-281/): Customer from Hampton got in touch regarding her front door. It was locking and unlocking, but it wouldn't stay on the latch.
- [Locksmith Ashford 280](https://eprlocksmith.co.uk/locksmith-ashford-280/): Customer from Ashford called saying he needed locks fitted to his bedroom doors for privacy reasons. They had just finished renovating and this was also on their to-do list.
- [Locksmith Chesham 279](https://eprlocksmith.co.uk/locksmith-chesham-279/): Former customer from Chesham got in touch regarding a parking bollard I installed a few years back. She couldn't seem to open the lock anymore and wanted help getting it operational again.
- [Locksmith Feltham 278](https://eprlocksmith.co.uk/locksmith-feltham-278/): Customer from Feltham got in touch saying that he couldn't open the door from the inside anymore and asked if I could help.
- [Locksmith Sunbury 277](https://eprlocksmith.co.uk/locksmith-sunbury-277/): Customer from Sunbury called saying that she was locked out because the door lock wouldn't work anymore. She had the key, but the door wasn't opening.
- [Locksmith Brentford 276](https://eprlocksmith.co.uk/locksmith-brentford-276/): A customer in Brentford got in touch after her car had been broken into and her purse, documents and house keys were stolen. She needed me to gain entry to her flat and change the door lock so the stolen keys could no longer be used.
- [Locksmith Staines 275](https://eprlocksmith.co.uk/locksmith-staines-275/): An aluminium sliding door in Staines was opened after a seized cylinder and failed multipoint gearbox, then adapted to a replacement system because the original was discontinued.
- [Locksmith Walton-on-Thames 274](https://eprlocksmith.co.uk/locksmith-walton-on-thames-274/): A customer in Walton-on-Thames got in touch because the mechanism on the front door was becoming harder and harder to operate. From the description, I suspected the gearbox was close to the end of its life and quoted for a replacement. The customer agreed and I arranged the repair for that afternoon.
- [Locksmith Ashford 273](https://eprlocksmith.co.uk/locksmith-ashford-273/): A customer in Ashford got in touch because the lock on the patio door had stopped working and asked if I could help.
- [Locksmith Sunbury 272](https://eprlocksmith.co.uk/locksmith-sunbury-272/): A customer in Sunbury got in touch for an emergency call-out after snapping the key in the door lock and still being unable to get the door open.
- [Locksmith Twickenham 271](https://eprlocksmith.co.uk/locksmith-twickenham-271/): A former customer in Twickenham got in touch about a fire door that they wanted to be able to lock. Several nearby doors already had matching locking hardware, but for whatever reason this particular door had not been done at the same time.
- [Locksmith Stanwell 270](https://eprlocksmith.co.uk/locksmith-stanwell-270/): This job followed directly from Locksmith Stanwell 283. The patio door had a broken lock component, but the bigger problem was that the multipoint mechanism itself was not releasing and the door would not open.
- [Locksmith Stanwell 269](https://eprlocksmith.co.uk/locksmith-stanwell-269/): A customer in Stanwell got in touch about a patio door after part of the lock had broken away. It does happen, although I do not see this particular type of break very often.
- [Locksmith Feltham 268](https://eprlocksmith.co.uk/locksmith-feltham-268/): A customer in Feltham got in touch because the front door lock had stopped working properly. The key would still unlock the door, but it would no longer lock it again, which meant the customer could not simply leave the house and secure the door behind them.
- [Locksmith Ashford 267](https://eprlocksmith.co.uk/locksmith-ashford-267/): A customer in Ashford was struggling to close the main door on an aluminium bi-fold set serving an outbuilding. From the description over the phone, I initially suspected that the multipoint lock might be failing or already broken, so I quoted on that basis before attending.
- [Locksmith Staines 266](https://eprlocksmith.co.uk/locksmith-staines-266/): A former customer in Staines got in touch because the French doors leading to the garden were blocked shut and could no longer be opened.
- [Locksmith Shepperton 265](https://eprlocksmith.co.uk/locksmith-shepperton-265/): A customer in Shepperton got in touch because they wanted the front door locks changed.
- [Locksmith Staines 264](https://eprlocksmith.co.uk/locksmith-staines-264/): An estate agent in Staines got in touch because a couple living in a second-floor flat were locked inside and could not open their front door.
- [Locksmith Sunbury 263](https://eprlocksmith.co.uk/locksmith-sunbury-263/): A customer in Sunbury-on-Thames got in touch because the front door was draughty and had also become a little difficult to lock.
- [Locksmith Ashford 262](https://eprlocksmith.co.uk/locksmith-ashford-262/): A customer in Ashford got in touch because the patio door would no longer lock.
- [Locksmith Feltham 261](https://eprlocksmith.co.uk/locksmith-feltham-261/): The landlord of an apartment block in Feltham got in touch because the communal entrance door was no longer locking.
- [Locksmith Addlestone 260](https://eprlocksmith.co.uk/locksmith-addlestone-260/): A customer in Addlestone got in touch because the mechanism on the garden sliding door would not engage, leaving the door unable to lock.
- [Locksmith Weybridge 259](https://eprlocksmith.co.uk/locksmith-weybridge-259/): A former customer from Ashford got back in touch after moving into a flat in Weybridge. The balcony door was letting in a lot of cold air and they asked me to see whether I could sort it out.
- [Locksmith Ashford 258](https://eprlocksmith.co.uk/locksmith-ashford-258/): A former customer in Ashford got in touch because she was not happy with the way her garden gate was being secured. A small padlock was being used and the outside of the gate also had exposed fixings that did very little to inspire confidence.
- [Locksmith Walton-on-Thames 257](https://eprlocksmith.co.uk/locksmith-walton-on-thames-257/): A returning customer in Walton got in touch about the garden gate because the existing arrangement did not feel secure enough, particularly with the property close to a busy road.
- [Locksmith Weybridge 256](https://eprlocksmith.co.uk/locksmith-weybridge-256/): A customer in Weybridge got in touch after buying a property and wanted several of the locks changed.
- [Locksmith Slough 255](https://eprlocksmith.co.uk/locksmith-slough-255/): A Slough door lock fault turned out to be the sash lock case rather than the barrel, so I replaced the failed case and kept the working cylinder.
- [Locksmith Slough 254](https://eprlocksmith.co.uk/locksmith-slough-254/): A neglected digital push-button lock in Slough was stiff and slow to return, so I cleaned and lubricated the mechanism and reset the code.
- [Locksmith Sunbury 253](https://eprlocksmith.co.uk/locksmith-sunbury-253/): A Sunbury customer had the door lock upgraded to a 1-star British Standard cylinder and the worn uPVC handles replaced with the correct size.
- [Locksmith Staines 252](https://eprlocksmith.co.uk/locksmith-staines-252/): A heavily rusted garden-door lock in Staines was replaced, then the keep and backbox were adjusted so the door latched correctly.
- [Locksmith Ashford 251](https://eprlocksmith.co.uk/locksmith-ashford-251/): An unusual aluminium window mechanism in Ashford could not be matched directly, so I adapted the existing keeps to make a suitable replacement work.
- [Locksmith Feltham 250](https://eprlocksmith.co.uk/locksmith-feltham-250/): A Feltham front door had an unusual double-spindle gearbox failure causing unreliable handle and key operation, so I sourced and fitted the correct replacement.
- [Locksmith Chiswick 249](https://eprlocksmith.co.uk/locksmith-chiswick-249/): A bathroom door in Chiswick was stuck shut after the latch spindle broke apart, so I opened the door and fitted a new fire-rated latch.
- [Locksmith Shepperton 248](https://eprlocksmith.co.uk/locksmith-shepperton-248/): A Shepperton composite door could no longer be operated properly from the handle, and testing confirmed that the multipoint gearbox had failed.
- [Locksmith Feltham 247](https://eprlocksmith.co.uk/locksmith-feltham-247/): A Feltham garden door could only be locked from one side, so I replaced the failed gearbox and worn handles and carried out a slight realignment.
- [Locksmith Feltham 246](https://eprlocksmith.co.uk/locksmith-feltham-246/): A Feltham tilt-and-turn balcony door had a broken gearbox and several locking keeps out of position, so I repaired and realigned the system.
- [Locksmith Feltham 245](https://eprlocksmith.co.uk/locksmith-feltham-245/): A Feltham customer snapped a key inside the front door lock. I removed the broken piece without replacing the existing lock.
- [Locksmith New Malden 244](https://eprlocksmith.co.uk/locksmith-new-malden-244/): A New Malden front door had dropped out of alignment, leaving a large gap and making the multipoint lock difficult to operate.
- [Locksmith Farnham 243](https://eprlocksmith.co.uk/locksmith-farnham-243/): A Farnham garage door had a failed gearbox that was no longer available, so I replaced the complete multipoint mechanism and realigned the door.
- [Locksmith Sandhurst 242](https://eprlocksmith.co.uk/locksmith-sandhurst-242/): A Sandhurst garden door was jammed solid after metal broke inside the gearbox. A double-spindle setup helped me open it without sacrificing the cylinder.
- [Locksmith Walton-on-Thames 241](https://eprlocksmith.co.uk/locksmith-walton-on-thames-241/): A Walton-on-Thames patio door had been forced until the key bent and the gearbox failed, so I replaced the gearbox and adjusted the locking system.
- [Locksmith Ashford 240](https://eprlocksmith.co.uk/locksmith-ashford-240/): An Ashford communal door was difficult to operate and both the lock case and cylinder were in poor condition, so I replaced the complete setup.
- [Locksmith Feltham 239](https://eprlocksmith.co.uk/locksmith-feltham-239/): A Feltham garden door had one bent hinge, one missing hinge and only the bottom hinge holding on, so I replaced the hinges and realigned the door.
- [Locksmith Guildford 238](https://eprlocksmith.co.uk/locksmith-guildford-238/): A large Guildford sliding door had an obsolete failed mechanism, so I removed the door from its rollers, repaired the lock and freed the seized rollers.
- [Locksmith Feltham 237](https://eprlocksmith.co.uk/locksmith-feltham-237/): A Feltham front door could only be opened with the key, and broken metal pieces were falling from the gearbox, so I replaced it from stock.
- [Locksmith Twickenham 236](https://eprlocksmith.co.uk/locksmith-twickenham-236/): A Twickenham front door had a missing latch and failed multipoint gearbox, so I restored the mechanism with a new gearbox, cylinder and adjustments.
- [Locksmith Richmond 235](https://eprlocksmith.co.uk/locksmith-richmond-235/): A Richmond communal nightlatch was badly fitted and could deadlock keyholders outside, so I replaced the backbox with a more suitable type.
- [Locksmith Ashford 234](https://eprlocksmith.co.uk/locksmith-ashford-234/): An Ashford garden door had a multipoint gearbox sheared in half. I secured the door overnight and returned with a genuine replacement mechanism.
- [Locksmith Walton-on-Thames 233](https://eprlocksmith.co.uk/locksmith-walton-on-thames-233/): A Walton bi-fold door had a broken handle and serious misalignment, so I adjusted the master door and later fitted the correct replacement handle.
- [Locksmith Ashford 232](https://eprlocksmith.co.uk/locksmith-ashford-232/): An Ashford customer was locked out with more than one broken key fragment inside the cylinder. I extracted them and saved the existing lock.
- [Locksmith Sunbury 231](https://eprlocksmith.co.uk/locksmith-sunbury-231/): A Sunbury front-door latch was sticking halfway and the door could blow open, so I secured it overnight and returned with the correct gearbox.
- [Locksmith Ashford 230](https://eprlocksmith.co.uk/locksmith-ashford-230/): An Ashford apartment entrance was blocked shut by a completely seized nightlatch, so I opened the door and fitted a replacement from stock.
- [Locksmith Ashford 229](https://eprlocksmith.co.uk/locksmith-ashford-229/): An Ashford commercial unit had security grilles but no keys, so I replaced the grille locks and keyed them alike for easier access.
- [Locksmith Sunbury 228](https://eprlocksmith.co.uk/locksmith-sunbury-228/): A Sunbury uPVC door handle would lift but the multipoint lock did nothing, so I replaced the failed gearbox and adjusted the system.
- [Locksmith Staines 227](https://eprlocksmith.co.uk/locksmith-staines-227/): Staines French doors stopped locking after an internal multipoint part broke, so I fitted the replacement from stock and realigned the doors.
- [Locksmith Ashford 226](https://eprlocksmith.co.uk/locksmith-ashford-226/): An Ashford customer wanted extra privacy and security for a bedroom, so I fitted a 3-lever fire-rated deadlock after discussing the options.
- [Locksmith Ashford 225](https://eprlocksmith.co.uk/locksmith-ashford-225/): An Ashford customer wanted extra security for a roller-shutter garage door, so I fitted an additional internal ABUS lock with a Yale Diskus padlock.
- [Locksmith Ashford 224](https://eprlocksmith.co.uk/locksmith-ashford-224/): An Ashford customer wanted a higher-security back-door lock, so I fitted a British Standard 3-star replacement cylinder from van stock.
- [Locksmith Ashford 223](https://eprlocksmith.co.uk/locksmith-ashford-223/): A large Ashford bathroom window had badly bent hinges and missing screws. I replaced the hinges and found a separate obsolete locking-mechanism fault.
- [Locksmith Ashford 222](https://eprlocksmith.co.uk/locksmith-ashford-222/): An Ashford customer wanted additional security on a wooden front door, so I installed a British Standard deadlock with care around the existing finish.
- [Locksmith Marlow 221](https://eprlocksmith.co.uk/locksmith-marlow-221/): A Marlow sliding-door bolt lock had become unreliable, so I sourced the correct replacement and returned to fit it despite other door issues.
- [Locksmith Windsor 220](https://eprlocksmith.co.uk/locksmith-windsor-220/): A Windsor bi-fold set had a bowed frame severe enough for the top guide to scrape aluminium, so I deglazed and realigned the complete system.
- [Locksmith Ashford 219](https://eprlocksmith.co.uk/locksmith-ashford-219/): An Ashford patio door was becoming difficult to lock, but testing with the door open showed the mechanism was sound and the real fault was alignment.
- [Locksmith Shepperton 218](https://eprlocksmith.co.uk/locksmith-shepperton-218/): A Shepperton multipoint lock had a spinning key and stiff handles, so I replaced the worn gearbox and adjusted the hinges and keeps.
- [Locksmith Egham 217](https://eprlocksmith.co.uk/locksmith-egham-217/): A uPVC front door in Egham had a previous workaround removed and the correct gearbox, split spindle and latch hold-back handles fitted.
- [Locksmith Bourne End 216](https://eprlocksmith.co.uk/locksmith-bourne-end-216/): A heavy Bourne End sliding door had dropped and was grinding on the floor after a roller component failed, so I sourced and fitted the correct roller set.
- [Locksmith Sunbury 215](https://eprlocksmith.co.uk/locksmith-sunbury-215/): Two Sunbury uPVC windows were blocked shut even though the locking mechanisms were sound. Both handles had failed internally and were replaced from stock.
- [Locksmith Richmond 214](https://eprlocksmith.co.uk/locksmith-richmond-214/): A Richmond uPVC window would not open even though the handle moved freely. I opened it carefully and repaired the failed section of the locking mechanism.
- [Locksmith Ashford 213](https://eprlocksmith.co.uk/locksmith-ashford-213/): A returning Ashford customer needed a bathroom door and lock installed in an awkward, badly out-of-square frame.
- [Locksmith Twickenham 212](https://eprlocksmith.co.uk/locksmith-twickenham-212/): A Twickenham school wanted a thumb-turn cylinder, and inspection showed the existing snap-protected lock had been fitted the wrong way round.
- [Locksmith Isleworth 211](https://eprlocksmith.co.uk/locksmith-isleworth-211/): An Isleworth property had no keys and a failed drilling attempt on the lock, so I replaced it with a fire-rated thumb-turn cylinder.
- [Locksmith Stanwell 210](https://eprlocksmith.co.uk/locksmith-stanwell-210/): A Stanwell front-door nightlatch was badly misaligned and poorly fixed, so I straightened the lock, corrected the fixings and restored normal operation.
- [Locksmith Isleworth 209](https://eprlocksmith.co.uk/locksmith-isleworth-209/): An Isleworth garage-door handle was spinning freely because the operating cable had snapped, so I opened the door and repaired the mechanism.
- [Locksmith Weybridge 208](https://eprlocksmith.co.uk/locksmith-weybridge-208/): A Weybridge patio door stopped opening after becoming increasingly stiff. A second spindle helped me open it before fitting and aligning a new mechanism.
- [Locksmith Stanwell 207](https://eprlocksmith.co.uk/locksmith-stanwell-207/): A Stanwell customer wanted a Yale Conexis smart lock installed, but the gearbox and door alignment first needed repairing so the system would work properly.
- [Locksmith Staines 206](https://eprlocksmith.co.uk/locksmith-staines-206/): A Staines garage door had become too difficult to use because its operating mechanism was bent, so I replaced the mechanism and adjusted the hardware.
- [Locksmith Isleworth 205](https://eprlocksmith.co.uk/locksmith-isleworth-205/): An Isleworth front-door multipoint lock had the wrong gearbox fitted during an earlier repair attempt, so I installed the correct part and realigned the door.
- [Locksmith Fleet 204](https://eprlocksmith.co.uk/locksmith-fleet-204/): After a break-in in Fleet, I measured and replaced a damaged double-glazed window unit and fitted a new window handle.
- [Locksmith Laleham 203](https://eprlocksmith.co.uk/locksmith-laleham-203/): A Laleham front-door lock had become difficult to use, so I replaced the failing unit with a British Standard lock from van stock.
- [Locksmith Slough 202](https://eprlocksmith.co.uk/locksmith-slough-202/): A Slough customer wanted a cat flap in a double-glazed uPVC door, so I measured, ordered and fitted a made-to-measure replacement glazing unit.
- [Locksmith Staines 201](https://eprlocksmith.co.uk/locksmith-staines-201/): A Staines front door was jammed shut by a failed multipoint gearbox and spindle, so I opened it through the failed mechanism and secured it overnight.
- [Locksmith Staines 200](https://eprlocksmith.co.uk/locksmith-staines-200/): A Staines door would not lock and the key was trapped because the cylinder cam was stuck inside the gearbox, so I released it and replaced the gearbox.
- [Locksmith Isleworth 199](https://eprlocksmith.co.uk/locksmith-isleworth-199/): An old Isleworth balcony sliding door was blocked shut by a failed mechanism, so I opened it carefully, sourced the required part and repaired the lock.
- [Locksmith Ashford 198](https://eprlocksmith.co.uk/locksmith-ashford-198/): An Ashford patio door was jammed shut after the multipoint mechanism seized around a 3-star cylinder, so I opened it and replaced the failed parts.
- [Locksmith Hampton 197](https://eprlocksmith.co.uk/locksmith-hampton-197/): A Hampton bi-fold door was locking intermittently because the gearbox spindle had lost teeth, so I secured it overnight and fitted a replacement centre case.
- [Locksmith New Malden 196](https://eprlocksmith.co.uk/locksmith-new-malden-196/): A New Malden customer lost her keys and wanted the front-door lock changed, revealing a poor previous nightlatch installation during the replacement.
- [Locksmith Kingston 195](https://eprlocksmith.co.uk/locksmith-kingston-195/): A Kingston upon Thames tenant wanted a cat flap without altering the landlord's original door panel, so I installed it in a new replacement uPVC panel.
- [Locksmith Maple Cross 194](https://eprlocksmith.co.uk/locksmith-maple-cross-194/): A Maple Cross customer wanted a cat flap in a detailed wooden door, so I positioned the opening carefully and completed a sealed installation.
- [Locksmith Ashford 193](https://eprlocksmith.co.uk/locksmith-ashford-193/): An Ashford patio door had an intermittently failing multipoint gearbox, so I replaced the worn gearbox from stock and adjusted the door.
- [Locksmith Bentley 192](https://eprlocksmith.co.uk/locksmith-bentley-192/): A Bentley door glazing unit was smashed while gardening, so I measured, ordered and fitted a matching UV-resistant replacement.
- [Locksmith Shepperton 191](https://eprlocksmith.co.uk/locksmith-shepperton-191/): Around 10 pairs of loose ceramic door knobs in Shepperton needed attention, so I drilled and threaded the spindles and secured them with new bolts.
- [Locksmith Ashford 190](https://eprlocksmith.co.uk/locksmith-ashford-190/): An Ashford uPVC door had a cracked gearbox spindle, but the existing multipoint mechanism was saved using a compatible replacement component.
- [Locksmith Ashford 189](https://eprlocksmith.co.uk/locksmith-ashford-189/): An Ashford customer was locked out even with the correct key. I gained access and traced the fault to a failed internal part in the lock backbox.

## Pages

- [Enquiry sent](https://eprlocksmith.co.uk/contact/thank-you/): ✓ Enquiry sent Thanks — your message has been sent. Your enquiry has been passed to EPRLocksmith. I’ll get back to you as soon as I can. Call 07454 482395Back to home If the problem is urgent, calling is the quickest way to reach me. Any photos attached to the form were sent with the enquiry and removed from the website afterwards.
- [Locksmith Egham](https://eprlocksmith.co.uk/areas/egham/): I provide mobile locksmith, lock, door and window repair services in Egham from my base in Ashford. Egham sits within a practical local working area for me, so I can cover the town without stretching the service area unnecessarily far from base. I cover Englefield Green, Thorpe, Staines-upon-Thames, Virginia Water and nearby areas. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Egham I already have documented locksmith work in Egham, including a uPVC door mechanism failure. That is exactly the type of fault […]
- [Locksmith Weybridge](https://eprlocksmith.co.uk/areas/weybridge/): I provide mobile locksmith, lock, door and window repair services in Weybridge from my base in Ashford. I deal with both standard locks and the mechanical faults found in modern multipoint doors. I cover Walton-on-Thames, Addlestone, Byfleet, Hersham and nearby areas. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Weybridge Previous Weybridge jobs have included multipoint lock failures and malfunctions, deadlock problems, security upgrades and uPVC balcony-door adjustment. That mix is why the diagnosis matters. Sometimes the failed lock or gearbox needs replacing; […]
- [Locksmith Hounslow](https://eprlocksmith.co.uk/areas/hounslow/): I provide mobile locksmith, lock, door and window repair services in Hounslow from my base in Ashford. There is no call centre: enquiries and jobs are handled directly by me. I cover Feltham, Hanworth, Isleworth, Osterley and nearby areas. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Hounslow Work I have previously carried out in Hounslow has included shop and glass-door lock work, internal door latches and general locksmith repairs. Commercial and residential doors can use very different hardware, so identifying what is […]
- [Locksmith Staines-upon-Thames](https://eprlocksmith.co.uk/areas/staines-upon-thames/): I provide mobile locksmith, door and window repairs in Staines-upon-Thames from nearby Ashford. I work independently and regularly attend lock and multipoint door faults across Staines and the surrounding area. I cover Ashford, Egham, Laleham, Stanwell and nearby areas. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Staines-upon-Thames I have attended many different Staines jobs over the years, including jammed and failed multipoint locks, doors blocked shut, uPVC door adjustment, nightlatch faults, damaged locks, digital lock work and standard lock changes. Multipoint failures […]
- [Lock Installation & Security Upgrades](https://eprlocksmith.co.uk/services/lock-replacements-upgrades/): Sometimes the job is not to repair a failed lock but to fit a new one: after moving home, losing keys, improving security, adding a second locking point or bringing an older door up to a more suitable standard. I install new locks and security upgrades without replacing unrelated hardware unnecessarily. New lock installation I fit mortice deadlocks and sash locks, nightlatches, cylinders and additional locking points to suitable timber, metal and other doors. The door construction, existing hardware and how the door is used all matter when deciding what type of lock makes sense. British Standard and high-security options British […]
- [Patio, Sliding & Bi-fold Door Repairs](https://eprlocksmith.co.uk/services/patio-sliding-bifold-doors/): Patio, sliding and bi-fold doors are heavy mechanical systems, not just a lock fitted to a large door. I repair locking mechanisms, handles, hinges, rollers and alignment faults where a patio door will not lock, a sliding door is difficult to operate or a bi-fold system has dropped or stopped closing correctly. Patio door lock and mechanism repairs Typical patio door problems include failed gearboxes, broken handles, locking points that will not engage, doors that have dropped and mechanisms that are difficult to operate. A patio door lock repair may involve the lock itself, but it can also require adjustment so […]
- [uPVC Window Mechanism & Hinge Repairs](https://eprlocksmith.co.uk/services/upvc-window-repairs/): If a uPVC window will not lock, is jammed shut, the handle has stopped working or the sash no longer pulls tightly into the frame, the failed part is usually the locking mechanism, handle, hinges or alignment. Customers understandably call these window lock problems; technically, most modern uPVC windows use a simplified multipoint mechanism inside the sash. uPVC window locking mechanism repairs I repair window espagnolette and locking mechanisms, including windows that are stuck shut or where the handle moves without operating the locking points. The mechanism is identified before parts are ordered or replaced because lengths, backsets and connection details […]
- [uPVC Door & Multipoint Lock Repairs](https://eprlocksmith.co.uk/services/upvc-door-lock-repairs/): A uPVC door that will not lock, has a stiff or floppy handle, or needs the key forced round often has a problem somewhere in the multipoint locking system. I repair uPVC, composite and many aluminium entrance doors, including gearboxes, full locking strips, handles, hinges, keeps and alignment faults. uPVC door lock and multipoint mechanism faults The central gearbox is a common failure point, but it is not the only one. Hooks or rollers can jam, a full strip can fail, handles can wear, or the door can drop enough for the locking points to bind against the keeps. Replacing only […]
- [Lock Repairs & Replacements](https://eprlocksmith.co.uk/services/door-lock-repairs/): If a front door lock is stiff, loose, unreliable or has stopped working altogether, the answer is not always to replace everything. I repair and replace traditional door locks, cylinders, nightlatches, mortice locks, deadlocks, sash locks, handles and related hardware. Door lock repair before replacement People often search for a door lock repair when the real fault could be inside the lock, in the cylinder, in the handle or in the way the door sits in the frame. I check what is actually causing the problem first. If a serviceable part can be retained, I would rather do that than replace […]
- [Emergency Locksmith](https://eprlocksmith.co.uk/services/emergency-locksmith/): If you are locked out, a lock has failed, a key has snapped or a door will no longer secure properly, I provide an emergency locksmith service from Ashford across nearby areas. I work independently, so the person you speak to is the locksmith who attends. When an emergency locksmith is needed Emergency locksmith work is not limited to lost keys. Common callouts include nightlatches that will not retract, keys that turn without operating the lock, multipoint mechanisms that fail with the door shut, broken cylinders and doors that suddenly will not lock because the mechanism or alignment has given up. […]
- [Locksmith Walton-on-Thames](https://eprlocksmith.co.uk/areas/walton-on-thames/): I provide mobile locksmith, door and window repairs in Walton-on-Thames, including conventional locks, multipoint systems, windows, gates and bi-fold doors. I cover Hersham, Weybridge, Molesey, Sunbury and nearby areas. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Walton-on-Thames I have carried out a broad mix of work in Walton-on-Thames, including multipoint gearbox failures, complete multipoint troubleshooting, flat-door lock changes, window locking mechanisms, bi-fold handle repairs and a lock installation on a garden gate. One Walton job involved a front-door cylinder spinning freely because […]
- [Locksmith Sunbury-on-Thames](https://eprlocksmith.co.uk/areas/sunbury-on-thames/): I provide mobile locksmith, door and window repair services in Sunbury-on-Thames from my base in nearby Ashford. The work ranges from conventional locks to multipoint doors, windows and larger patio or bi-fold systems. I cover Ashford, Shepperton, Hampton, Walton-on-Thames and nearby areas. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Sunbury-on-Thames Previous work in Sunbury has included multipoint gearbox and lock repairs, uPVC door realignment, door handles and lock changes, locked-out callouts, uPVC window hinges and bi-fold door handle work. Those jobs are […]
- [Locksmith Feltham](https://eprlocksmith.co.uk/areas/feltham/): I provide mobile locksmith, door and window repair services in Feltham from my base in nearby Ashford. I work independently, so the person answering the phone is the person who attends the job. I cover Hanworth, Bedfont, Hounslow, Ashford and the surrounding area. Fair pricing, no hidden fees, and I carry a broad range of common locks, cylinders, gearboxes, handles and repair parts in the van. Locksmith work in Feltham Feltham is one of the areas where I have carried out a wide range of work rather than one type of callout. Previous jobs have included multipoint lock failures, uPVC door […]
- [Locksmith Ashford](https://eprlocksmith.co.uk/areas/ashford/): If you are looking for a locksmith in Ashford, Middlesex, EPRLocksmith is based here. I work independently, so the person answering the phone is the person who attends the job. There is no call centre and no subcontractor roulette. I deal with lock problems, difficult doors, uPVC and composite door mechanisms, windows, patio and sliding doors, lock changes and emergency faults across Ashford and the surrounding area. Fair pricing, no hidden fees, and most common repair parts are carried in the van. Lock, door and window repairs in Ashford Not every door that will not lock needs a new lock. A […]
- [Locksmith in Ashford](https://eprlocksmith.co.uk/): Lock repairs, lock replacements, emergency lockouts and uPVC door lock repairs across Ashford and surrounding areas. Call EPR Locksmith for a fast, local and reliable locksmith service. Call 07454 482395 Locksmith Services EPR Locksmith provides a range of domestic locksmith services across Ashford and nearby areas. Emergency Locksmith Locked out or need urgent help with a faulty lock? Call for emergency locksmith support. Lock Replacement Replacement locks supplied and fitted for doors, windows, garages and more. uPVC Door Repair Repairs for uPVC doors, faulty mechanisms, stiff handles and door lock problems. Multipoint Lock Repair Repair and replacement of multipoint locking systems […]
- [Contact EPRLocksmith](https://eprlocksmith.co.uk/contact/): If a lock, door or window is giving you trouble, call me directly or send the details below. For urgent problems, calling is usually the quickest option. For repairs and quotations, a few clear photographs can be very useful before I attend. Before you send it Three things that help me understand the job quickly 01What is it doing? Tell me what happens when you turn the key, lift the handle, close the door or operate the window. 02Where are you? A town or postcode helps me judge travel and availability before arranging the visit. 03Send useful photos One photo of […]
- [Reviews](https://eprlocksmith.co.uk/reviews/)
- [Recent Work](https://eprlocksmith.co.uk/recent-work/): Recent Locksmith Work Here are examples of locksmith work carried out across Ashford and surrounding areas. Recent Jobs Multipoint Lock Repair in Sunbury A faulty multipoint locking system was inspected and repaired for a customer in Sunbury. Nightlatch Replacement in Feltham A worn nightlatch was replaced to improve the security and everyday use of the front door. Patio Door Lock Repair in Staines A patio door lock problem was repaired for a customer in Staines. uPVC Door Lock Repair in Ashford A uPVC door lock issue was checked and repaired so the door could lock correctly again. Lock Replacement in Walton-on-Thames […]
- [About EPRLocksmith](https://eprlocksmith.co.uk/about/): I am Lucian, the locksmith behind EPRLocksmith. I run the business independently from Ashford, Middlesex, so the person you speak to is the person who attends the job. A locksmith with an engineering approach My background is in mechanical engineering, and that naturally shapes the way I work. A door that will not lock is not always simply a bad lock. A failed gearbox, worn hinges, poor alignment, badly positioned keeps or another mechanical fault can all create the same symptom. I prefer to work out what has actually failed before replacing parts. Sometimes the answer is a new lock or […]
- [Areas Covered](https://eprlocksmith.co.uk/areas/): EPRLocksmith is an independent mobile locksmith based in Ashford, Middlesex. I mainly work across the nearby towns shown below, keeping the core service area deliberately local rather than trying to cover half of the South East. Core locksmith areas These eight town pages are the main local areas I focus on. Each one links to genuine work carried out in and around that location as those jobs are migrated onto the new site. Why keep it local? A practical service area Keeping the main coverage centred on Ashford means less time lost travelling between jobs and more chance of dealing with […]
- [Locksmith Services](https://eprlocksmith.co.uk/services/): I repair more than conventional locks. A lot of the work I attend involves the mechanics around the lock: multipoint gearboxes, door alignment, hinges, window mechanisms, patio and sliding door systems, handles and worn hardware. The six service areas below cover the work I most commonly carry out. If you are not sure which one applies, describe what the door, window or lock is doing rather than trying to diagnose it yourself. Repair first, replace when necessary A stiff handle or a door that will not lock does not automatically mean the complete locking system needs replacing. I check what has […]
- [Privacy Policy](https://eprlocksmith.co.uk/privacy-policy/): Last updated: 18 September 2026. This privacy notice explains how Lucian Talpos trading as EPRLocksmith uses personal information when you contact me, ask for a quotation, book work, use this website or interact with customer-review content shown on it. Who is responsible for your information Lucian Talpos trading as EPRLocksmith is the data controller for the personal information described in this notice. You can contact me at info@eprlocksmith.co.uk or 07454 482395. Information I may collect Depending on how you contact me and the work requested, this may include your name, telephone number, email address, town or postcode, service address, photographs you […]

## Optional

- [Agent (MCP protocol)](websites-agents.hostinger.com/eprlocksmith.co.uk/mcp)

[comment]: # (Generated by Hostinger Tools Plugin)